| Material Information
||Construction Inspection Report for The Department of General Services
||Historic St. Augustine: Permits, State Inspections, City Forms, HARB
|Divider: ||DOS 8449-A, Govt. House 87-88|
|Folder: ||Permits, State Inspections, City Forms, HARB|
||Saint Augustine (Fla.)
48 King Street (Saint Augustine, Fla.)
Government House (Saint Augustine, Fla.)
||North America -- United States of America -- Florida -- Saint Johns -- Saint Augustine -- 48 King Street
||29.892465 x -81.313142
| Record Information
||University of Florida
||University of Florida
||All rights reserved by the source institution and holding location.
Area: CONSTRUCTION INSPECTION REPORT
The Department of General Services
TO: Administrator FROM: Curtis C. Holmes, Jr., Inc.
Design Review and Permitting Section (Inspection Firm)
Department of General Services
Room 512, Larson Building
Tallahassee, FL 32301
State Project #:/ Project Name: Correct Life Safety Violations / Renovate
East Wing, Government House, St. Augustine
Type of Inspection:Mechanical HVAC Performed by: David Bruce Miller, P.E., Mech. Eng.
(one type per report)
Date of Inspection: 1-25-89 Time in: 10:30 A.M. Time out: 11:30 A.M.
Prime/General Contractor: Historic St. Augustine Board Superintendent: Dave Scott
Subcontractor: Masters Heating & Air Conditioning Foreman: Everett Masters
Clerk of the Works: N/A Weather conditions: Fair Warm
List work inspected, Code violations (including specific Code references) and
resolutions, other relevant comments: NOTE: A/E must resolve all code violations
otherwise a stop work order will be issued..
ACTIVITIES: Rough-in.inspection east wing.
1) New first floor system:
a) "York" air-source heat pump air conditioning system with horizontal air handling
unit located in below-floor slab perimeter trench (utilized as return-air plenum)
and outdoor condensing unit located on 2nd floor roof. According to Everett
Masters, unit size is nominal 5-ton.
b) Soft copper refrigerant suction and liquid piping with flexible, elastomeric
tubing insulation installed on suction line. Running trap located in 2nd floor
attic horizontal suction line downstream of suction riser.
c) Sheet metal supply ductwork (located in perimeter trench) with external wrap
blanket insulation serving floor-mounted supply register boots located along
north wall. Insulated round flex duct runouts, having spin-in fittings w/damper,
connect to .uninsulated sheet metal supply register boots.
c) Return air floor grille openings (located along south wall) to perimeter trench
return air plenum below.
e) Thermostat control cable wiring partly installed. Exposed cable section serving
outdoor condensing unit and running horizontally with refrigerant piping on
2nd floor roof is subject to damage.
cc: A/E (continued next page) (Inspector's nature)
January 30, 1989
page 1 of2 Rev: 6/1i
CONSTRUCTION INSPECTION REPORT Mechanical HVAC Inspection
Project #DOS-84490010 (8449-A) January 25, 1989
f) Outdoor condensing unit mounted on extended 4 x 4 wood runners set in pitch
pockets on sloped roof. Low end of unit provided with black-material shims,
high end mounted directly on runner.
g) Combustible wood joists and form boards located in perimeter trench return-air
plenum, along with short section of plastic tube, wiring, and PVC condensate
h) Dual-switch condensate pump set located adjacent to air handling unit in
perimeter trench R/A plenum. Uninsulated 1/2" copper pump discharge line
connects to 3/4" copper condensate drain riser of 2nd floor unit. Common
3/4" drain then discharges into existing rain leader.
2) Existing second floor system:
a) Existing outdoor condensing unit relocated from porch roof to 2nd floor roof
and mounted on abovementioned extended 4 x 4 wood runners adjacent to new
first floor outdoor condensing unit.
b) Existing air handling unit condensate drain relocated. Drain runs horizontally
in 1st floor ceiling to north wall and down to side tap connection to existing
rain leader. Insulated horizontal section bowed up by other trades should be
adjusted for uniform slope.
CONCLUSIONS: Inspected work satisfactory, subject to comments below.
COMMENTS: Attention is called to the following items for A/E and Contractor
consideration and resolution:
a) Combustible materials in R/A plenum should be protected per
Std. Mech. Code, para. 512.2.
b) Insulation of sheet metal floor register boots, per Std. Mech.
Code, para. 506.2.1.
c) Automatic fan shutdown control, per Std. Mech. Code, para. 515.1.
d) Addition of pipe supports raising refrigerant piping and control
cable (serving condensing unit) above 2nd floor roof a few inches to
permit rainwater to flow to roof drain,
Page 2 of 2